Model 9150 operators are designed to operate vehicular slide gates in residential, commercial and industrial applications. These operators are designed so that they can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. In addition, the operators can be pad or post mounted to meet any installation requirements. The 9150 can be equipped with a factory installed DC Convenience Open option which will automatically open the gate in the event of a power outage.
Electronic, automatically adjusted limit settings (no mechanical limit switches required).
Mechanical and electronic inherent entrapment sensing system operable in both the open and close direction.
Automatic close timer is adjustable from 1 to 23 seconds.
Two ports for plug-in loop detectors.
Partial open feature opens gate to 14 ft (4.3 meters)
Special Anti-Talegate loop function helps prevent vehicles from gaining entry by talegating.
Gate Tracker™ reporting feature sends gate operator data to a companion DoorKing access control system.
Optional Battery Back-Up drive system opens gate automatically, or on command, during power outages.
SPEED: Approximately 1 ft. (.3 meter) per second.
CHAIN:#40 Roller Chain Standard.
MAXIMUM GATE WEIGHT: 1000 pounds (453 kilograms) for the 1/2 Horsepower, or 1500 pounds (679 kilograms) for the 1 Horsepower.
MAXIMUM GATE LENGTH: 30 feet (9.2 meters) for the 1/2 Horsepower, or 45 feet (13.7 meters) for the 1 Horspower.
WEIGHT: Approximately 125 pounds (56.5 kilograms) to 185 pounds (83.7 kilograms) depending on options selected.
The Model 9100 operator is designed to operate vehicular slide gates in residential and commercial applications. The 9100 is designed so that it can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. In addition, the operator can be pad or post mounted to meet any installation requirements.
The Model 9310 operator is for vehicular slide gates in residential and commercial locations. The 9310 is designed so that it can easily be mounted in the front or rear of the gate without any costly and time consuming field modifications. This operator is designed to be pad mounted. The 9310 is available in one-half or one horspower versions. It can be equipped with a factory installed DC convenience open option which will automatically open the gate in the event of a power outage.
Direct driven manual limits.
Power Start circuit (1/2 HP only).
Anti-tailgating feature.
Gate tracker reporting output.
Ports for plug-in loop detectors.
DC Powered convenience open (optional).
Two convenience outlets.
Fail-safe release (fail-secure optional).
Programming switches.
Built-in reset switch.
Built-in power On/Off switch.
DC powered convenience open.
Nickel plated chain.
Stainless steel chain.
Heater kit for cold environments.
Surge suppressors.
SPECIFICATIONS, Model 9310 , half horsepower :
Maximum gate length 30-feet.
Maximum gate weight 1000 pounds. (Assumes gate is on level ground, in good condition with properly adjusted hardware. If DC Convenience Open option is installed, maximum gate weight is 800 pounds. Other external factors may affect the performance of the gate operator.)
10:1 gear reduction running in a continuous oil bath.
1/2 HP continuous-duty motor.
115, 208, 230, 460 VAC*. (*208, 230 and 460 volt units use a step-down power transformer to achieve 115 volt operating voltage.)
Operator is shipped with chain brackets and 20-feet of #40 chain.
Class I, II, III and IV applications.
Compliant with UL 325 and 991. ETL Listed. Note: To be compliant with UL 325 and industry safety guidelines, a secondary entrapment prevention device(s) is required to be installed with this gate operator. We can provide you with more details on these devices and on current industry safety standards.
Dimensions: 21.5 inches wide x 27.5 inches high x 16.5 inches deep.
SPECIFICATIONS, Model 9310 , One horsepower :
Maximum gate length 45-feet.
Maximum gate weight 1500 pounds. (Assumes gate is on level ground, in good condition with properly adjusted hardware. If DC Convenience Open option is installed, maximum gate weight is 1300 pounds. Other external factors may affect the performance of the gate operator.)
10:1 gear reduction running in a continuous oil bath.
Operator is shipped with chain brackets and 20-feet of #40 chain.
Class I, II, III and IV applications.
Compliant with UL 325 and 991. ETL Listed. Note: To be compliant with UL 325 and industry safety guidelines, a secondary entrapment prevention device(s) is required to be installed with this gate operator. We can provide you with more details on these devices and on current industry safety standards.
Dimensions: 28.5 inches wide x 27.5 inches high x 16.5 inches deep.
